Following successful private and public previews, Microsoft has begun deploying Windows Customer-side Translator (WinCLAT) through Controlled Feature Rollout (CFR) to Windows 11 clients. WinCLAT allows IPv4-dependent applications to operate on IPv6-only and IPv6-mostly networks, removing an important compatibility barrier for organizations transitioning away from native IPv4. As of September 23, 2026, I estimate that approximately half of eligible Windows endpoints have received the feature, with availability expected to expand over the next several weeks.
What Is CLAT?
CLAT (customer-side translator) is part of the 464XLAT IPv6 transition and translation technology. CLAT uses the Stateless IP/ICMP Translation Algorithm (SIIT) to translate IPv4 packets generated by the client into IPv6. A corresponding provider-side translator (PLAT), typically a NAT64 gateway, translates the packets back to IPv4 before forwarding them to their destination.
Background
CLAT has been part of Windows for quite some time. It first shipped with Windows Phone and was later ported to Windows 10 with the Creators Update (v1703) in April 2017. Until now, the implementation was limited to wireless wide area network (WWAN) cellular interfaces.
Why Do We Need CLAT?
Although modern applications increasingly support IPv6, many applications and services still depend on IPv4. Some applications use IPv4-only sockets or application programming interfaces (APIs), while others connect directly to literal IPv4 addresses. Because these applications cannot use DNS64-generated AAAA records, they require another mechanism to communicate across an IPv6-only network. WinCLAT provides this compatibility while allowing the network to operate without native IPv4 connectivity.
How WinCLAT Works
When enabled, WinCLAT determines whether the client is operating without native IPv4 connectivity. This can occur on an IPv6-only network or an IPv6-mostly network where Dynamic Host Configuration Protocol for IPv4 (DHCPv4) Option 108 instructs capable clients to forgo an IPv4 address. WinCLAT then learns the network’s NAT64 prefix from a router advertisement (RA) or via DNS and the ipv4only.arpa domain. Next, WinCLAT creates a synthetic IPv4 address on the network interface. When an application generates IPv4 traffic, WinCLAT statelessly translates the IPv4 packets to IPv6 using the discovered NAT64 prefix and forwards them to the network. Return traffic is translated back to IPv4. This process is transparent to most applications, which can continue using IPv4 sockets without native IPv4 connectivity on the network.
SLAAC Requirement
WinCLAT currently requires the client to obtain its IPv6 address using Stateless Address Autoconfiguration (SLAAC). It does not work on networks that assign client IPv6 addresses exclusively through stateful DHCPv6. Organizations using DHCPv6 for IPv6 address assignment must also enable SLAAC before deploying WinCLAT.
The Role of DNS64 and NAT64
DNS64 and NAT64 work alongside WinCLAT to provide access to IPv4-only resources from an IPv6-only network. Their role depends on whether an application communicates using IPv6 or still requires IPv4.
IPv4 Connectivity for IPv6 Applications
DNS64 synthesizes AAAA records from IPv4 A records, allowing IPv6-capable applications to communicate with IPv4-only destinations through the NAT64 gateway. Applications that use IPv4 sockets or connect to literal IPv4 addresses cannot use these synthesized records and instead rely on WinCLAT for compatibility.
NAT64 Prefix Discovery
DNS also provides one method for WinCLAT to discover the network’s NAT64 prefix. WinCLAT can obtain the prefix by querying ipv4only.arpa, although the preferred method is the PREF64 option in an IPv6 router advertisement.
Note: DNS64 and NAT64 are likely familiar to Microsoft DirectAccess administrators, as these technologies were introduced with DirectAccess in Windows Server 2012.
Configure WinCLAT
After the WinCLAT feature becomes available on your device, you can enable and configure it using netsh.exe.
Enable WinCLAT
To permit WinCLAT operation on non-cellular interfaces, open an elevated command window and run the following command.
netsh.exe interface clat set global permit=enabled
View WinCLAT Settings
You can view the current global configuration by running the following command.
netsh.exe interface clat show global
You can also view interface-specific settings using the following command.
netsh.exe interface clat show instance interface=<interface name>
Prefix Discovery
Optionally, you can enable or disable NAT64 prefix discovery options (from DNS and/or from RA) using the following commands.
# enable pref64 discovery methodsnetsh.exe interface clat set global pref64fromdns=enablednetsh.exe interface clat set global pref64fromra=enabled
# disable pref64 discovery methodsnetsh.exe interface clat set global pref64fromdns=disablednetsh.exe interface clat set global pref64fromra=disabled
Note: At least one prefix-discovery method must remain enabled. When both are enabled, WinCLAT prefers the PREF64 option in an IPv6 router advertisement and uses DNS-based discovery as a fallback.
WinCLAT IPv4 Address
WinCLAT assigns 192.0.0.1/32 to the interface for use by the local IPv4 stack. This address comes from the IANA-reserved 192.0.0.0/29 IPv4 Service Continuity Prefix defined in RFC 7335. Addresses from this prefix support local IPv4 compatibility and are not transmitted as IPv4 packets on the physical network.
Test IPv4 Connectivity
To test connectivity with WinCLAT, browse to a website or connect to another resource that uses IPv4 only from an IPv6-only network. In this example, I’m connecting to Google’s IPv4-only website https://ipv4.google.com/.
Group Policy
Administrators can also manage WinCLAT configuration settings using Active Directory (AD) and Group Policy. To begin, copy the tcpip.admx and tcpip.adml files from C:\Windows\PolicyDefinitions and C:\Windows\PolicyDefinitions\en-us (or another preferred language) from a device on which WinCLAT is available to the Group Policy Central Store in AD. Once complete, you will find WinCLAT settings in the following location in the Group Policy Management console (gpmc.msc).
Computer Configuration > Policies > Administrative Templates > Network > TCPIP Settings > IPv6 Transition Technologies
Summary
WinCLAT extends Windows support for 464XLAT to noncellular network interfaces, allowing IPv4-dependent applications to operate on IPv6-only and IPv6-mostly networks. It translates locally generated IPv4 traffic to IPv6 and forwards it to a NAT64 gateway, while DNS64 provides direct NAT64 connectivity for IPv6-capable applications. Administrators can configure WinCLAT locally using netsh.exe or centrally through Group Policy and can use either router advertisements or DNS to discover the NAT64 prefix. WinCLAT currently requires SLAAC-based IPv6 addressing and does not support networks that assign client IPv6 addresses exclusively through stateful DHCPv6.
Additional Information
Microsoft Plans to Extend CLAT Support in Windows 11
Microsoft Windows CLAT Public Preview
RFC 6877 – 464XLAT: Combination of Stateful and Stateless Translation