Always On VPN RRAS Internal Interface Non-Operational

Windows 10 Always On VPN Routing Configuration

Always On VPN administrators troubleshooting connectivity issues may find the Internal network interface in the Routing and Remote Access management console (rrasmgmt.msc) administrative status indicates ‘Unknown’. They will also notice the Operational Status shows Non-operational.

Internal Interface

For clarification, the ‘Internal’ network interface in the Routing and Remote Access management console, as shown above, is not a physical network adapter on the server. Instead, it is a virtual network interface used only for incoming VPN connections.

Non-Operational

The Internal virtual network interface will not be created until the VPN server accepts its first VPN connection. Because of this, the Internal interface will have an operational status of non-operational until the first client attempts to connect. When this occurs, RRAS creates the interface, then assigns it the first IP address from the static IPv4 address pool. Alternatively, if DHCP is configured, it will assign the first IP address returned by the DHCP server.

Interface Names

While discussing network interfaces, I typically recommend renaming them in Windows to identify their function, especially when using two NIC configurations. However, be careful not to name the server’s internal network adapter ‘Internal’, as this can be confusing in the future. In my example above, I use the name ‘LAN’ to identify the internal adapter to distinguish it from the server’s ‘Internal’ virtual interface.

Additional Information

Windows Server RRAS Service Does Not Start

Windows Server RRAS Monitoring and Reporting

Microsoft Always On VPN and RRAS in Azure

Microsoft Always On VPN and RRAS with Signle NIC

Always On VPN Video Training Course on Pluralsight

Implementing Microsoft Windows Always On VPN, my latest video training course on Pluralsight is now available! This course provides comprehensive training for designing, implementing, and supporting a Windows Always On VPN solution. The course is nearly seven hours long (!) and covers all Always On VPN configuration aspects. The video training course covers the following Always On VPN topics.

  • Infrastructure planning and preparation
  • Configuring VPN infrastructure
  • Provisioning Always On VPN clients
  • Advanced configuration
  • Always On VPN in Azure
  • Certificates and Intune
  • High availability
  • Monitoring and reporting
  • Troubleshooting

The Implementing Always On VPN video training course is available to Pluralsight subscribers now. You can sign up for a free trial if you don’t have a subscription. Enjoy!

Additional Information

Implementing Microsoft Windows Always On VPN on Pluralsight

Additional Video Training Courses on Pluralsight

Sign Up for a Free Trial at Pluralsight

Inbox Accounting Database Management

The Routing and Remote Access Service (RRAS) role in Windows Server is a popular VPN server choice for administrators deploying Windows Always On VPN. It is easy to configure, scales well, and is cost-effective. After installing RRAS, administrators can optionally enable inbox accounting to log historical data and generate user access and activity reports as described in Always On VPN RRAS Monitoring and Reporting.

Inbox Accounting Database

A Windows Internal Database (WID) is automatically installed and configured for data storage when inbox accounting is enabled.

WID is nothing more than a basic instance of Microsoft SQL Server. As such, the database will require periodic maintenance to perform optimally.

Inbox Accounting Database Management Scripts

I have created a series of PowerShell scripts to address the inbox accounting database management requirements for organizations using Windows Server RRAS. Scripts are available to perform the following inbox accounting database management tasks.

  • Optimize the inbox accounting database.
  • View the size of the inbox accounting database files.
  • Compress the size of the inbox accounting database.
  • Back up the inbox accounting database to a file on disk.
  • Restore the inbox accounting database from a backup file.
  • Move the inbox accounting database file to a different location.
  • Remove the inbox accounting database.

Optimize Database

A known issue with the inbox accounting database can result in high CPU and memory utilization for very busy RRAS VPN servers. Specifically, a crucial index is missing from one of the tables in the logging database. This issue persists in Windows Server 2022. To correct this issue, download and run the following PowerShell script on each RRAS VPN server in the organization.

Optimize-InboxAccountingDatabase.ps1

View Database Size

The database can grow rapidly depending on how busy the RRAS server is. Administrators can view the current database file sizes by downloading and running the following PowerShell script on the RRAS server.

Get-InboxAccountingDatabaseSize.ps1

Compress Database

Over time, the database can become fragmented, decreasing performance. Compressing the database can improve performance and result in significant recovery of disk space. To compress the inbox accounting database, download and run the following PowerShell script on each RRAS server in the organization.

Compress-InboxAccountingDatabase.ps1

In this example, compressing the database reduced its size by more than 8MB, resulting in a nearly 70% reduction in disk space usage.

Backup Database

Administrators may wish to back up the inbox accounting database before purging older records from the inbox accounting database. Also, backing up the database preservers access records when migrating to a new server. To back up the inbox accounting database, download and run the following PowerShell script on each RRAS server in the organization.

Backup-InboxAccountingDatabase.ps1

Restore Database

Naturally, to restore the inbox accounting database from a previous backup, administrators can download and run the following PowerShell script.

Restore-InboxAccountingDatabase.ps1

Restoring a database from backup will erase all records in the current database. It does not append. Proceed with caution!

Move Database Files

Inbox accounting database and log files are located in C:\Windows\DirectAccess\Db by default.

However, storing database and log files on the system drive is not ideal. A better alternative is to place the inbox accounting database and log files on a separate disk for optimum performance. To move the inbox accounting database, download and run the following PowerShell script on each VPN server in the organization.

Move-InboxAccountingDatabase.ps1

Moving inbox accounting files may not be formally supported by Microsoft. Use caution when making this change.

Remove Database

Occasionally an inbox accounting database becomes corrupt and can no longer be managed. If this happens, completely removing the database is required. It is essential to know that simply disabling and re-enabling inbox accounting on the VPN server does not delete the database. To delete the database completely, download and run the following PowerShell script.

Remove-InboxAccountingDatabase.ps1

PowerShell Module

To simplify things, the PowerShell scripts described in this article are available in a PowerShell module that can be installed from the PowerShell gallery using the following command.

Install-Module InboxAccountingDatabaseManagement

Additional Information

Windows Always On VPN RRAS Inbox Accounting Database Management PowerShell Module

Windows Always On VPN RRAS Monitoring and Reporting

Windows Always On VPN PowerShell Scripts on GitHub

Always On VPN Error -2146762495

DirectAccess Troubleshooting and the Windows 10 Network Connectivity Assistant

Always On VPN Administrators may encounter a scenario where Always On VPN connections suddenly stop working for all clients using the Secure Socket Tunneling Protocol (SSTP) VPN protocol. IKEv2 VPN connections continue to work, however.

Event Log

Reviewing the event log on a client machine reveals an error event ID 20227 from the RasClient source. The error message states the following.

“The user [username] dialed a connection named [connection name] which has failed. The error code returned on failure is -2146762495.”

Error -2146762495?

Always On VPN administrators will be familiar with error codes such as 809, 691 and 812, 853, 858, and even 13801, 13806, and 13868. However, this error code seems to be formatted much differently. As it turns out, this message is in decimal format. Thankfully it’s pretty easy to convert it to something more meaningful, like hexadecimal. To do this, open the Windows calculator (calc.exe) and switch to programmer mode. Highlight DEC and enter -2146762495. The hexadecimal value will be displayed in the HEX field, as shown here.

Error 0x800B0101

After converting the error message from decimal to hex, use the Microsoft Error Lookup tool (err.exe) to translate the hex value of this error. As shown here, 0x800B0101 translates to CERT_E_EXPIRED.

Expired TLS Certificate

Once again, an expired certificate is to blame! In this case, the TLS certificate installed on the VPN server has expired and is no longer valid.

Resolution

The problem is simple enough to resolve, of course. Obtain a new TLS certificate from your certification authority (CA) of choice and update your VPN server configuration. You can find detailed guidance for updating the RRAS VPN server’s TLS certificate here. You will also find a video demonstration of the RRAS SSL/TLS certificate renewal process here.

Additional Information

Installing or Renewing an SSL/TLS Certificate on Windows Server RRAS for Always On VPN and SSTP

VIDEO: Installing or Renewing an SSL/TLS certificate on Windows Server RRAS for Always On VPN and SSTP

Microsoft Windows Always On VPN SSTP Security Configuration

Microsoft Windows Always On VPN SSL/TLS Certificate Requirements for SSTP

Microsoft Windows Always On VPN SSTP with Let’s Encrypt Certificates

Always On VPN SSTP Certificate Renewal

Windows Server Routing and Remote Access Service (RRAS) is popular for Always On VPN deployments because it supports the Secure Socket Tunneling Protocol (SSTP). The SSTP VPN protocol is recommended for use with the Always On VPN user tunnel because it is firewall friendly. Installing a TLS certificate on the VPN server is necessary to support SSTP VPN connections. Administrators should use a TLS certificate signed by a public certification authority (CA) for optimal reliability and performance.

Click here to view a video demonstration of the procedures outlined in this article.

Certificate Expiration

Of course, all certificates expire, and the TLS certificate used for SSTP is no exception. When using a public TLS certificate, the certificate lifetime is typically no more than one year, which means Always On VPN administrators will be renewing this certificate regularly.

Certificate Renewal

The process of “renewing” an SSTP TLS certificate is essentially the same as installing a new one, as it is best to create a new public/private key pair when renewing a certificate. The following outlines the steps required to generate a Certificate Signing Request (CSR), import the certificate, then assign the certificate to the SSTP listener on the VPN server.

Note: The guidance provided here assumes using an ECC certificate, which is best for optimal security and performance. More details here.

Certificate Request

Open the local computer certificate store (certlm.msc) on the VPN server and perform the following steps to generate a new CSR.

  1. Expand Certificates – Local Computer > Personal.
  2. Right-click the Certificates folder and choose All Tasks > Advanced Operations > Create Custom Request.
  3. Click Next.
  4. Highlight Proceed without enrollment policy.
  5. Click Next.
    1. Select (No template) CNG key from the Template drop-down list.
    2. Select PKCS #10 in the Request format section.
    3. Click Next.
  6. Click on the down arrow next to Details.
    Always On VPN ECDSA SSL Certificate Request for SSTP
  7. Click on the Properties button.
  8. Select the General tab.
    1. Enter the public hostname for the certificate in the Friendly name field.
  9. Select the Subject tab.
    1. Select Common name from the Type drop-down list in the Subject name section.
    2. Enter the public hostname for the certificate in the Value field.
    3. Click Add.
    4. In the Alternative name section, select DNS from the Type drop-down list.
    5. Enter the public hostname for the certificate in the Value field.
    6. Click Add.
      Always On VPN ECDSA SSL Certificate Request for SSTP
  10. Select the Extensions tab.
    1. Expand the Extended Key Usage section.
    2. Select Server Authentication from the Available options section.
    3. Click Add.
      Always On VPN ECDSA SSL Certificate Request for SSTP
  11. Select the Private Key tab.
    1. Expand the Cryptographic Service Provider section.
      1. Uncheck the box next to RSA,Microsoft Software Key Storage Provider.
      2. Check the box next to ECDSA_P256,Microsoft Software Key Storage Provider.
    2. Expand the Key options section.
      1. Check the box next to Make private key exportable.
        Always On VPN ECDSA SSL Certificate Request for SSTP
  12. Click Ok.
  13. Click Next.
  14. Enter a name for the file in the File Name field.
  15. Select Base 64 in the File format section.
  16. Click Finish.

Import Certificate

Once complete, submit the file created to a public CA for signing. When the CA returns the signed certificate, perform the following steps to import it to the local compute certificate store.

  1. Right-click the Certificates folder and choose All Tasks > Import.
  2. Click Next.
  3. Enter the name of the certificate file returned by the public CA in the File name field.
  4. Click Next.
  5. Select Place all certificates in the following store and ensure that Personal is listed in the Certificate store field.
  6. Click Next.
  7. Click Finish.
  8. Click Ok.

Assign Certificate

After importing the new TLS certificate in the local computer’s certificate store, open the Routing and Remote Access management console (rrasmgmt.msc) and perform the following steps to assign the TLS certificate to the SSTP listener.

  1. Right-click the VPN server and choose Properties.
  2. Select the Security tab.
    1. Select the new TLS certificate from the Certificate drop-down list in the SSL Certificate Binding section. When replacing an existing certificate, you may see a certificate with the same name more than once. Click the View button and ensure the new certificate is selected.
    2. Click Ok.
    3. Click Yes to restart the RemoteAccess service.

Demonstration Video

A recorded video demonstration of this process can be found here. The video recording also includes guidance for making these changes on Windows Server Core servers.

Additional Information

Installing or Renewing an SSL/TLS Certificate on Windows Server for Always On VPN and SSTP.

Microsoft Windows Always On VPN SSTP Security Configuration

Microsoft Windows Always On VPN SSL Certificate Requirements for SSTP

Microsoft Windows Always On VPN ECDSA TLS Certificate Request for SSTP

Microsoft Windows Always On VPN SSTP with Let’s Encrypt Certificates

Always On VPN IKEv2 Security Vulnerabilities – January 2022

The January 2022 security updates for Microsoft Windows include several important updates that will affect Always On VPN deployments. Specifically, CVE-2022-21849 addresses a Remote Code Execution (RCE) vulnerability that should be addressed immediately. The January 2022 security update also includes updates for several IKE Denial-of-Service (DoS) vulnerabilities, in addition to privilege escalation vulnerabilities in the Remote Access Connection Manager.

Update – January 17, 2022: Microsoft has released out-of-band updates to address the issues with IPsec (IKEv2 and L2TP) when using non-Microsoft VPN devices. Updates can be found here.

Update – January 13, 2022: There have been numerous reports of this update breaking VPN functionality when using non-Microsoft VPN devices. If you are using Windows Server and RRAS you can safely update. If you are using a third-party device, you may encounter problems. In addition, there have been reports of issues with domain controllers and Hyper-V servers after installing this update. Please proceed carefully and be sure to have a backup before updating!

Vulnerable Systems

These vulnerabilities are present on both Windows Server and Client operating systems. Essentially, any Windows server or client using IPsec is vulnerable and potentially exploitable.

Vulnerabilities

The following is a list of security updates related to Always On VPN deployments.

Windows IKE Extension Remote Code Execution (RCE) Vulnerability

Windows IKE Extension Denial of Service Vulnerabilities

Windows Remote Access Connection Manager Elevation of Privilege Vulnerability

Additional Information

A list of all fixes in the January 2022 security update, along with links to the updates themselves, can be found here.

Always On VPN SSTP Load Balancing with Citrix NetScaler ADC

Always On VPN SSTP Load Balancing with Citrix NetScaler ADCOne of the many advantages of using Windows Server Routing and Remote Access Service (RRAS) as the VPN server to support Windows 10 Always On VPN connections is that it includes support for the Secure Socket Tunneling Protocol (SSTP). SSTP is a TLS-based VPN protocol that is easy to configure and deploy and is very firewall friendly. This ensures consistent and reliable connectivity even behind restrictive firewalls. The Citrix ADC (formerly NetScaler) is a popular platform for load balancing Always On VPN connections. In this article I’ll describe how to configure load balancing on the Citrix ADC for RRAS VPN connections using the SSTP VPN protocol.

Special Note: In December 2019 a serious security vulnerability was discovered on the Citrix ADC that gives an unauthenticated attacker the ability to arbitrarily execute code on the appliance. As of this writing a fix is not available (due end of January 2020) but a temporary workaround can be found here.

Load Balancing SSTP

Previously I’ve written about some of the use cases and benefits of SSTP load balancing as well as the options for offloading TLS for SSTP VPN connections. Load balancing SSTP eliminates single points of failure and enables support for multiple RRAS VPN servers to increase scalability. It is generally recommended that the Citrix ADC be configured to pass through encrypted SSTP VPN connections. However, TLS offloading can be configured to improve performance and reduce resource utilization on VPN servers, if required.

Configuration

Load balancing SSTP on the Citrix ADC is straightforward and not unlike load balancing a common HTTPS web server. Below are specific settings and parameters required to load balance SSTP using the Citrix ADC.

Note: This article is not a comprehensive configuration guide for the Citrix ADC. It assumes the administrator is familiar with basic load balancing concepts and has experience configuring the Citrix ADC.

Service Settings

The load balancing service for SSTP VPN should be configured to use TCP port 443 and the SSL_BRIDGE protocol. If TLS offload is required, TCP port 80 and the HTTP protocol can be configured. Additional configuration is required on the RRAS server when TLS offload is enabled, however. Detailed information for configuring RRAS and SSTP for TLS offload can be found here.

Always On VPN SSTP Load Balancing with Citrix NetScaler ADC

Virtual Server Settings

The virtual server is configured to use TCP port 443. It is recommended to use SSLSESSION persistence.

Always On VPN SSTP Load Balancing with Citrix NetScaler ADC

The LEASTCONNECTION load balancing method is the recommend option for load balancing method.

Always On VPN SSTP Load Balancing with Citrix NetScaler ADC

Service Monitoring

Using the default TCP monitor (tcp-default) is not recommended for monitoring SSTP, as a simple TCP port check does not accurately reflect the health of the SSTP service running on the RRAS server. To more precisely monitor the SSTP service status, a new custom monitor must be created and bound to the load balancing services. Follow the steps below to configure a custom SSTP VPN monitor on the Citrix ADC.

  1. Open the Citrix ADC management console and expand Traffic Management.
  2. Select Monitors.
  3. Click Add.
  4. Enter a descriptive name in the Name field.
  5. Select HTTP form the Type drop-down list and click Select.
  6. Adjust the Interval and Response Time-out values according to your requirements.
  7. Enter 401 in the Response Codes field and click the “+” button.
  8. In the Response Codes field click the “x” next to 200.
  9. In the HTTP Request field enter HEAD /sra_{BA195980-CD49-458b-9E23-C84EE0ADCD75}/.
  10. Check the box next to Secure (not required if TLS offload is enabled).
  11. Select ns_default_ssl_profile_backend from the SSL profile drop-down list (not required if TLS offload is enabled).
  12. Click Create.

Always On VPN SSTP Load Balancing with Citrix NetScaler ADC

Once complete, bind the new service monitor to the load balancing services or service groups accordingly.

TLS Offload

It is generally recommended that TLS offload not be enabled for SSTP VPN. However, if TLS offload is desired, it is configured in much the same way as a common HTTPS web server. Specific guidance for enabling TLS offload on the Citrix ADC can be found here. Details for configuring RRAS and SSTP to support TLS offload can be found here.

Certificates

When enabling TLS offload for SSTP VPN connections it is recommended that the public SSL certificate be installed on the RRAS server, even though TLS processing will be handled on the Citrix ADC and HTTP will be used between the Citrix ADC and the RRAS server. If installing the public SSL certificate on the RRAS server is not an option, additional configuration will be required. Specifically, TLS offload for SSTP must be configured using the Enable-SSTPOffload.ps1 PowerShell script, which can be found here.

Once the script has been downloaded, open an elevated PowerShell command window and enter the following command.

.\Enable-SSTPOffload.ps1 -CertificateHash [SHA256 Certificate Hash of Public SSL Certificate] -Restart

Example:

.\Enable-SSTPOffload.ps1 -CertificateHash ‘C3AB8FF13720E8AD9047DD39466B3C8974E592C2FA383D4A3960714CAEF0C4F2’ -Restart

Re-Encryption

When offloading TLS for SSTP VPN connections, all traffic between the Citrix ADC and the RRAS server will be sent in the clear using HTTP. In some instances, TLS offload is required only for traffic inspection, not performance gain. In this scenario the Citrix ADC will be configured to terminate and then re-encrypt connections to the RRAS server. When terminating TLS on the Citrix ADC and re-encrypting connections to the RRAS server is required, the same certificate must be used on both the Citrix ADC and the RRAS server. Using different certificates on the RRAS server and the load balancer is not supported.

Additional Information

Always On VPN Load Balancing

Windows 10 Always On VPN Load Balancing and SSL Offload

SSL Offload Configuration for Citrix ADC (NetScaler)

Windows 10 Always On VPN SSTP Load Balancing with Kemp LoadMaster

Windows 10 Always On VPN SSTP Load Balancing with F5 BIG-IP

Windows 10 Always On VPN Connects then Disconnects

Windows 10 Always On VPN SSL Certificate Requirements for SSTP

Always On VPN RRAS Monitoring and Reporting

Always On VPN RRAS Monitoring and ReportingWindows Server with the Routing and Remote Access Service (RRAS) role installed is a popular choice for Windows 10 Always On VPN deployments. Configuring RRAS is commonly performed using the RRAS management console but it can also be configured using PowerShell and/or netsh. In addition, there are a few different options for natively monitoring server health and client connection status.

RRAS Management Console

After installing the RRAS role, the administrator uses the RRAS management console (rrasmgmt.msc) to perform initial configuration. The RRAS management console can also be used to view client connection status by expanding the server and highlighting Remote Access Clients.

Connection Details

To view connection details for a specific connection, the administrator can right-click a connection and choose Status, or simply double-click the connection.

High level information about the connection including duration, data transfer, errors, and IP address assignment can be obtained here. In addition, the administrator can terminate the VPN connection by clicking the Disconnect button.

RRAS Management Console Limitations

Using the RRAS management console has some serious limitations. It offers only limited visibility into client connectivity status, for example. In addition, the client connection status does not refresh automatically. Also, the RRAS management console offers no historical reporting capability.

Remote Access Management Console

The Remote Access Management console (ramgmtui.exe) will be familiar to DirectAccess administrators and is a better option for viewing VPN client connectivity on the RRAS server. It also offers more detailed information on connectivity status and includes an option to enable historical reporting.

Dashboard

The Dashboard node in the Remote Access Management console provides high-level status for various services associated with the VPN server. It also provides a high-level overview of aggregate VPN client connections.

Operations Status

The Operations Status node in the Remote Access Management console provides more detailed information regarding the status of crucial VPN services. Here the administrator will find current status and information about service uptime.

Remote Client Status

The Remote Client Status node in the Remote Access Management console is where administrators will find detailed information about client connectivity. Selecting a connection will provide data about the connection including remote IP addresses, protocols, and ports accessed by the remote client, in addition to detailed connection information such as authentication type, public IP address (if available), connection start time, and data transferred.

Always On VPN RRAS Monitoring and Reporting

Double-clicking an individual connection brings up a detailed client statistics page for the connection, as shown here.

Always On VPN RRAS Monitoring and Reporting

Custom View

The Remote Access Management console includes the option to customize the data presented to the administrator. To view additional details about client connections, right-click anywhere in the column headings to enable or disable any of the fields as required.

Always On VPN RRAS Monitoring and Reporting

Recommended Columns

From personal experience I recommend adding the following columns in the Remote Access Management console.

  • IPv4 Address (this is the IP address assigned to the VPN clients by RRAS)
  • Connection Start Time
  • Authentication Method
  • Total Bytes In
  • Total Bytes Out
  • Rate

Always On VPN RRAS Monitoring and Reporting

Drawbacks

The only real drawback to using the Remote Access Management console is that it supports viewing connections from just one VPN server at a time. If you have multiple RRAS servers deployed, you must retarget the Remote Access Management console each time to view connections on different VPN servers in the organization.

You can retarget the Remote Access Management console at any time by highlighting the Configuration node in the navigation pane and then clicking the Manage a Remote Server link in the Tasks pane.

Always On VPN RRAS Monitoring and Reporting

Reporting

Remote Access reporting is not enabled by default on the RRAS VPN server. Follow the steps below to enable historical reporting for RRAS VPN connections.

1. Highlight the Reporting node in the Remote Access Management console.
2. Click Configure Accounting.
3. Uncheck Use RADIUS accounting.
4. Check Use inbox accounting.
5. Review the settings for data retention and make changes as required.
6. Click Apply.

Always On VPN RRAS Monitoring and Reporting

Optionally, historical reporting can be enabled using PowerShell by opening and elevated PowerShell command window and running the following command.

Set-RemoteAccessAccounting -EnableAccountingType Inbox -PassThru

Database Management

A Windows Internal Database (WID) is automatically installed and configured for data storage when inbox accounting is enabled. WID is nothing more than a basic instance of Microsoft SQL Server. As such, the database will require periodic maintenance to perform optimally. I have published the InboxAccountingDatabaseManagement PowerShell module to address many of the required and optional administrative tasks associated with inbox accounting. You can learn more about this PowerShell module and its functions here.

https://directaccess.richardhicks.com/2022/03/21/inbox-accounting-database-management/

Important Note! There is a known issue with the inbox accounting database that can result in high CPU utilization for very busy RRAS VPN servers. Specifically, a crucial index is missing from one of the tables in the logging database. To correct this issue, be sure to run the Optimize-InboxAccountingDatabase function included in my InboxAccountingDatabaseManagement PowerShell module.

Additional Information

Always On VPN Inbox Accounting Database Management

Always On VPN Inbox Accounting Database Management PowerShell module on Github

Windows 10 Always On VPN and Windows Routing and Remote Access Service (RRAS)

Windows 10 Always On VPN Protocol Recommendations for Windows Server Routing and Remote Access Service (RRAS)

Windows 10 Always On VPN and RRAS with Single NIC

Windows 10 Always On VPN and RRAS in Microsoft Azure

Always On VPN IKEv2 Load Balancing Issue with Kemp LoadMaster

Always On VPN IKEv2 Load Balancing Issue with Kemp LoadMasterA recent update to the Kemp LoadMaster load balancer may cause failed connections for Always On VPN connections using IKEv2. SSTP VPN connections are unaffected.

Load Balancing IKEv2

When using the Kemp LoadMaster load balancer to load balance IKEv2, custom configuration is required to ensure proper operation. Specifically, the virtual service must be configured to use “port following” to ensure both the initial request on UDP port 500 and the subsequent request on UDP port 4500 are sent to the same real server. This requires the virtual service to be configured to operate at layer 7. Detailed configuration guidance for load balancing IKEv2 on the Kemp LoadMaster load balancer can be found here.

Always On VPN IKEv2 Load Balancing Issue with Kemp LoadMaster

Issues with LMOS 7.2.48.0

A recent release of the Load Master Operating System (LMOS) v7.2.48.0 introduced a bug that affects UDP services configured to operate at layer 7, which includes IKEv2. This bug breaks Always On VPN connections using IKEv2, resulting in failed connections. When this occurs, the administrator may encounter an error 809 message for device tunnel or user tunnel.

Always On VPN IKEv2 Load Balancing Issue with Kemp LoadMaster

Update Available

Administrators who use the Kemp LoadMaster load balancer to load balance Always On VPN IKEv2 connections and have updated to LMOS 7.2.48.0 are encouraged to update to LMOS 7.2.48.1 immediately. This latest update includes a fix that resolves broken IKEv2 load balancing for Always On VPN. Once the LoadMaster has been updated to 7.2.48.1, Always On VPN connections using IKEv2 should complete successfully.

Additional Information

Windows 10 Always On VPN IKEv2 Load Balancing and NAT

Windows 10 Always On VPN IKEv2 Load Balancing with Kemp LoadMaster Load Balancer

Windows 10 Always On VPN SSTP Load Balancing with Kemp LoadMaster Load Balancer

Windows 10 Always On VPN Load Balancing with Kemp LoadMaster in Azure

Windows 10 Always On VPN Load Balancing Deployment Guide for Kemp Load Balancers

Always On VPN and RRAS in Azure

Always On VPN and RRAS in AzureWhen deploying Windows 10 Always On VPN, it may be desirable to host the VPN server in Microsoft’s Azure public cloud. Recently I wrote about Always On VPN deployment options in Azure, and in that post I indicated that deploying Windows Server and the Routing and Remote Access Service (RRAS) was one of those options. Although not formally supported by Microsoft, RRAS is often deployed in Azure because it is cost-effective, easy to manage, and provides flexible scalability.

Supportability

It’s important to state once again that although it is possible to successfully deploy Windows Server with RRAS in Azure to support Always On VPN, as of this writing it is not a formally supported workload. If the administrator makes the decision to deploy RRAS in Azure, they must also accept that Microsoft may refuse to assist with troubleshooting in this specific deployment scenario.

Always On VPN and RRAS in Azure

Reference: https://support.microsoft.com/en-us/help/2721672/microsoft-server-software-support-for-microsoft-azure-virtual-machines

Azure Prerequisites

The configuration of RRAS is identical to on-premises, with a few additional steps required by Azure infrastructure.

Windows Server

RRAS can be configured on any Windows Server virtual machine supported in Microsoft Azure. As with on-premises deployments, Server GUI and Core are supported. Domain-join is optional. The server can be deployed with one network interface or two.

Public IP

A public IP address must be assigned to the VPN server’s external network interface, or the internal interface if the VPN server is configured with a single network adapter. The IP address can be static or dynamic. When using a dynamic IP address, configure a CNAME record in DNS that points to the name configured for the IP address in Azure. If using a static IP address, an A host record can be configured pointing directly to the IP address.

Network Security Group

A Network Security Group (NSG) must be configured and assigned to the VPN server’s external or public-facing network interface that allows the following protocols and ports inbound.

  • TCP port 443 (SSTP)
  • UDP port 500 (IKEv2)
  • UDP port 4500 (IKEv2 NAT traversal)

RRAS in Azure

Below are the infrastructure requirements for supporting Windows Server RRAS VPN in Azure.

Client IP Subnet

Static IP address pool assignment must be used with RRAS. Using DHCP for VPN client IP address assignment in Azure is not supported and will not work. The IP subnet assigned to VPN clients by RRAS must be unique and not overlap with any existing Azure VNet subnets. If more than one VPN server is deployed, each server should be configured to assign a unique subnet for its clients.

IP Forwarding

IP forwarding must be enabled on the VPN server’s internal network interface. Follow the steps below to enable IP forwarding.

1. In the Azure portal, open the properties page for the internal network interface for the VPN server.
2. Click IP configurations in the navigation pane.
3. Click Enabled next to IP forwarding.
4. Click Save.

Always On VPN and RRAS in Azure

Routing

Azure must be configured to route IP traffic from VPN clients back to the VPN server. Follow the steps below to create and assign a routing table in Azure.

1. Click Create Resource.
2. Enter “Route Table” in the search field and press Enter.
3. Click Route Table.
4. Click Create.
5. Enter a descriptive name for the route table in the Name field.
6. Choose an appropriate subscription from the Subscription drop-down list.
7. Select the resource group where the VPN server(s) reside.
8. Select the best location to deploy the route table resource from the Location drop-down list.
9. If the administrator wants to have the VPN client IP subnet route information published automatically, select Enabled for Virtual network gateway route propagation.
10. Click Create.

Always On VPN and RRAS in Azure

Once complete, follow the steps below to define the route for VPN clients.

1. Open the properties page for the route table.
2. Click Routes in the navigation pane.
3. Click Add.
4. Enter a descriptive name in the Route name filed.
5. Enter the IP subnet assigned to VPN clients in the Address prefix field.
6. Select Virtual appliance from the Next hop type drop-down list.
7. Enter the IPv4 address assigned to the VPN server’s internal network interface in the Next hop address field.
8. Click Ok.
9. Repeat the steps above for each VPN server configured in Azure.

Always On VPN and RRAS in Azure

Finally, follow the steps below to assign the route table to an Azure VNet subnet.

1. Open the properties page for the route table.
2. Click Subnets in the navigation pane.
3. Click Associate.
4. Click Virtual network.
5. Choose the appropriate Azure VNet.
6. Click Subnet.
7. Choose an Azure VNet subnet to assign the route table to.
8. Click Ok.
9. Repeat the steps above to assign the route table to any Azure VNet subnet that must be accessible by VPN clients. If VPN clients need access to on-premises resources via Azure site-to-site gateway, assign the route table to the Azure VPN gateway subnet.

Always On VPN and RRAS in Azure

Note: Azure only supports the assignment of one route table per subnet. If a route table is currently assigned, the VPN client subnet route can be added to an existing route table, if necessary.

Summary

Administrators have many choices when it comes to support Always On VPN connections hosted in Azure. RRAS on Windows Server can be an effective solution, assuming you can live without formal support. If having a formally supported solution is a hard requirement, consider deploying Always On VPN using the native Azure VPN gateway or another third-part Network Virtual Appliance (NVA).

Additional Information

Windows 10 Always On VPN with Azure Gateway

Windows 10 Always On VPN Options for Azure Deployments

Windows 10 Always On VPN Multisite with Azure Traffic Manager