The Internet Key Exchange version 2 (IKEv2) VPN protocol is the protocol of choice when the highest level of security is required for Always On VPN connections. It uses IPsec and features configurable security parameters that allow administrators to adjust policies to meet their specific security requirements. IKEv2 is not without some important limitations, but organizations may insist on the use of IKEv2 to provide the greatest protection possible for remote connected clients. Due to complexities of the IKEv2 transport, special configuration on the Citrix ADC (formerly NetScaler) is required when load balancing this workload.

Special Note: In December 2019 a serious security vulnerability was discovered on the Citrix ADC that gives an unauthenticated attacker the ability to arbitrarily execute code on the appliance. As of this writing a fix is not available (due end of January 2020) but a temporary workaround can be found here.

Load Balancing IKEv2

When an Always On VPN client establishes a connection using IKEv2, communication begins on UDP port 500, but switches to UDP port 4500 if Network Address Translation (NAT) is detected in the communication path between the client and the server. Because UDP is connectionless, custom configuration is required to ensure that VPN clients maintain connectivity to the same backend VPN server during this transition.

Initial Configuration

Load balancing IKEv2 using the Citrix ADC is similar to other workloads. Below are specific settings and parameters required to load balance IKEv2 using the Citrix ADC.

Note: This article is not a comprehensive configuration guide for the Citrix ADC. It assumes the administrator is familiar with basic load balancing concepts and has experience configuring the Citrix ADC.

Service Settings

The load balancing services for IKEv2 VPN will use UDP ports 500 and 4500. Create the service group and assign group members for UDP 500 as follows.

Repeat the steps above to create the service group for UDP port 4500.

Virtual Server Settings

Two virtual servers are required, one for UDP port 500 and one for UDP port 4500. Ensure that the service group using UDP port 500 is bound to the virtual server using the same port.

Repeat the steps above to create the virtual service for UDP port 4500.

Service Monitoring

Since IKEv2 uses the UDP protocol, the only option for service monitoring is to use PING, which is configured by default. Ensure that the firewall on the VPN server allows inbound ICMPv4 and ICMPv6 Echo Request. The default PING monitor on the Citrix ADC will ping the resource every 5 seconds. If a different interval is required, the administrator can edit the PING monitor and bind that to the service or service group as necessary.

Persistency Group

A Persistency Group on the Citrix ADC will be configured to ensure that IKEv2 VPN client requests from the same client are always routed to the same backend server. Follow the steps below to create a Persistency Group and assign it to both IKEv2 virtual servers created previously.

1. In the Citrix ADC management console expand Traffic Management > Load Balancing > Persistency Groups.
2. Click Add.
3. Enter a descriptive name for the Persistency Group.
4. Select SOURCEIP from the Persistence drop-down list.
5. Next to the Virtual Server Name section click the Add button.
6. Add both previously configured IKEv2 virtual servers for UDP 500 and 4500.
7. Click Create.

Use Client IP

To ensure reliable connectivity for IKEv2 VPN connections it is necessary for the VPN server to see the client’s original source IP address. Follow the steps below to configure the Service Group to forward the client’s IP address to the VPN server.

1. In the Citrix ADC management console expand System, click Settings, and then click Configure Modes.
2. Select Use Subnet IP.
3. Click Ok.
4. Expand Traffic Management, click Load Balancing, and then click Service Groups.
5. Select the IKEv2 UDP 500 Service Group.
6. Click Edit in the Settings section.
7. Select Use Client IP.
8. Repeat these steps on the IKEv2 UDP 4500 Service Group.

Note: Making the above changes will require configuring the VPN server to use the Citrix ADC as its default gateway.

Additional Information

Windows 10 Always On VPN IKEv2 Load Balancing and NAT

Windows 10 Always On VPN SSTP Load Balancing with Citrix NetScaler ADC

Windows 10 Always On VPN IKEv2 Features and Limitations

Windows 10 AlWAYS On VPN and IKEv2 Fragmentation

Windows 10 Always On VPN IKEv2 Security Configuration

Windows 10 Always On VPN Certificate Requirements for IKEv2