DirectAccess IP-HTTPS Preauthentication using Citrix NetScaler

Note: For information about configuring the F5 BIG-IP to perform IP-HTTPS preauthentication, click hereFor information about configuring Windows Server 2012 R2 or Windows Server 2016 to perform IP-HTTPS preauthentication natively, click here.

Introduction

DirectAccess IP-HTTPS Preauthentication using Citrix NetScalerIP-HTTPS is an IPv6 transition technology used by DirectAccess. It enables DirectAccess clients to communicate with the DirectAccess server using IPv6 over the public IPv4 Internet by encapsulating IPv6 packets in HTTP and authenticating (and optionally encrypting) them using SSL/TLS. IP-HTTPS is supported for all DirectAccess network deployment configurations and is enabled by default.

When a DirectAccess client connection is established, only the server is authenticated by the client. The client is not authenticated by the server. The DirectAccess server will thus accept IP-HTTPS connections from any client, valid or not.

IP-HTTPS Connection

Once a client has established an IP-HTTPS transition tunnel, it will go through the standard IPv6 neighbor discovery process to identify routers and obtain an IPv6 prefix for the link. It will use this information to build its own IPv6 address, which it uses to communicate with the DirectAccess server and begin establishing IPsec security associations for DirectAccess.

ICMP and IPsec

By design, ICMP is exempt from DirectAccess IPsec policy processing. If an unauthorized client were to establish an IP-HTTPS transition tunnel, even without authentication (Kerberos Proxy or certificate) it would be able to ping the DirectAccess server tunnel endpoint IPv6 addresses, the DNS64 IPv6 address, and any intranet hosts (assuming host firewalls allow this access).

Security Risk

This default posture opens up the DirectAccess server and intranet to unauthorized remote network reconnaissance and some IPv6-related Denial-of-Service (DoS) attacks. These were demonstrated by security researcher Ali Hardudi at the recent Troopers16 security conference. You can view his very informative session here.

Note: DirectAccess IPsec data connections are unaffected and are completely secure. Data is never exposed at any time with the default configuration.

IP-HTTPS Preauthentication

DirectAccess IP-HTTPS Preauthentication using Citrix NetScalerTo mitigate these risks, it is recommended that an Application Delivery Controller (ADC) such as the Citrix NetScaler be configured to preauthenticate DirectAccess clients prior to establishing the IP-HTTPS transition tunnel.

Note: To configure the F5 BIG-IP to perform IP-HTTPS preauthentication, click here.

Citrix NetScaler Configuration

To perform DirectAccess preauthentication, it will be necessary to configure the Citrix NetScaler to perform SSL termination for IP-HTTPS. The virtual server on the NetScaler must use the SSL protocol. In addition, a CA certificate must be bound to the virtual server. Also, Client Authentication must be enabled under SSL Parameters and be set to Mandatory.

DirectAccess IP-HTTPS Preauthentication using Citrix NetScaler

Once configured, the NetScaler appliance will ensure that the DirectAccess IPsec certificate is present on the client before establishing the IP-HTTPS IPv6 transition tunnel. This will prevent unauthorized connections to the DirectAccess server.

Important Considerations

Performing IP-HTTPS preauthentication on the Citrix NetScaler is formally unsupported by Microsoft. In addition, terminating IP-HTTPS on the NetScaler appliance breaks OTP authentication.

Summary

The default security posture of DirectAccess leaves the internal network open to unauthorized network reconnaissance, and exposes the DirectAccess infrastructure to potential denial-of-service (DoS) attacks. To mitigate these security risks, implement the Citrix NetScaler ADC and enable client certificate authentication.

References

Security Assessment of Microsoft DirectAccess [Overview] – https://www.insinuator.net/2016/04/security-assessment-of-microsoft-directaccess/

Security Assessment of Microsoft DirectAccess [Full Document] – https://www.ernw.de/newsfeed/newsletter-53-may-2016-security-assessment-of-microsoft-directaccess/index.html

Security Assessment of Microsoft DirectAccess Troopers16 Presentation by Ali Hardudi [Video] – https://www.youtube.com/watch?v=wW1x7ow0V9w

Chiron IPv6 Penetration Testing Framework – https://www.insinuator.net/2014/10/chiron-an-all-in-one-ipv6-penetration-testing-framework/

IP-HTTPS specification on MSDN – https://msdn.microsoft.com/en-us/library/dd358571.aspx

Configure F5 BIG-IP to Perform IP-HTTPS Preauthentication – https://directaccess.richardhicks.com/2016/05/23/directaccess-ip-https-preauthentication-using-f5-big-ip/

Configure Windows Server 2012 R2  and Windows Server 2016 to Perform IP-HTTPS Preauthentication – https://directaccess.richardhicks.com/2016/06/13/directaccess-ip-https-preauthentication/

%d bloggers like this: