Introduction
To provide geographic redundancy, DirectAccess can be deployed in a multisite configuration. In this scenario, Windows 8.x and Windows 10 clients are aware of all entry points in the enterprise and will automatically select the nearest available entry point to connect to. The nearest entry point is defined as the one that responds the quickest. When a Windows 8.x or Windows 10 client attempts to establish DirectAccess connectivity, an HTTP GET is sent to all entry points and the client will select the one with the shortest Round Trip Time (RTT) for the request.
Note: Windows 7 clients can be provisioned when DirectAccess is configured for multisite access, but they must be assigned to an individual entry point.
Challenges
There are a number of challenges that come with the default multisite configuration. Choosing an entry point based solely on network latency is rather simplistic and can often produce unexpected results. It also lacks support for granular traffic distribution or active/passive configuration.
GSLB
For the best experience, DirectAccess can be configured to use a Global Server Load Balancing (GSLB) solution to enhance transparent site selection and failover for Windows 8.x and Windows 10 clients. Commonly this is implemented using an on-premises appliance (Citrix NetScaler, F5 Global Traffic Manager, Kemp LoadMaster, A10 Thunder, etc.). These solutions offer exceptional control over DirectAccess traffic distribution, but they add expense and complexity.
Azure Traffic Manager
Azure Traffic Manager is a cloud-based GSLB solution that is a simple and cost-effective alternative to dedicated on-premises appliances. While it does not offer all of the features that GSLB appliances provide, it does provide better traffic distribution options than the default configuration. Importantly, it enables active/passive failover, which is a common requirement not supported natively with DirectAccess.
Traffic Manager Configuration
In the Azure portal (the new one, not the old one!) click New, Networking, and then Traffic Manager profile.
Provide a name and select a Routing method.
Routing method options are Performance, Weighted and Priority.
- Performance. Select this option to enable clients to connect to the entry point with the lowest network latency.
- Weighted. Select this option to enable clients to prefer some entry points more than others. Assign a weight value of 1 to 1000 for each entry point. Higher values have more preference. Values for entry points can be the same, if desired.
- Priority. Select this option to enable clients to connect to a primary entry point, then fail over to a secondary or tertiary entry point in the event of an outage. Assign a priority value of 1 to 1000 for each entry point. Lower values take precedence. Each entry point must be assigned a unique priority value.
Click Create when finished. Next click Settings for the new traffic manager profile and click Configuration. Change Protocol to HTTPS, Port to 443, and Path to /IPHTTPS. Click Save when finished.
Next click Endpoints and click Add. Select External endpoint from the drop down list, provide a descriptive name, and then enter the Fully-Qualified Domain Name (FQDN) of the first DirectAccess entry point. When using the Performance routing method, choose a location that best represents the geography where the DirectAccess entry point is located. When using the Weighted or Priority routing methods, specify an appropriate value accordingly. Click Ok when finished. Repeat these steps for each entry point in the organization.
DirectAccess Configuration
In the Remote Access Management console, highlight DirectAccess and VPN below Configuration in the navigation tree and then click Configure Multisite Settings below Multisite Deployment in the Tasks pane. Click Global Load Balancing and choose Yes, use global load balancing. Enter the FQDN of the Azure Traffic Manager profile and click Next, and then click Commit.
Note: An SSL certificate with a subject name matching that of the GSLB FQDN is not required.
In some cases, the management console may report that global load balancing addresses cannot be identified automatically for some or all entry points.
If this occurs, it will be necessary to run the Set-DAEntryPoint PowerShell cmdlet to assign GLSB IP addresses to each entry point. The GSLB IP address is the public IPv4 address that the entry point public hostname resolves to.
Set-DAEntryPoint -Name [entrypoint_name] -GslbIP [external_ip_address]
For example:
Set-DAEntryPoint -Name "US West" -GslbIP 203.0.113.195
Set-DAEntryPoint -Name "US East" -GslbIP 198.51.100.21
Summary
DirectAccess includes native functionality to enable geographic load balancing for Windows 8.x and Windows 10 clients. The site selection process used by DirectAccess clients in this scenario is basic, and has the potential to yield unexpected results. Azure Traffic Manager is a simple, cost-effective alternative to dedicated on-premises GSLB appliances. It can be integrated with DirectAccess to address some of the shortcomings with the native entry point selection process.
Additional Resources
Like this:
Like Loading...
Likely the single most common complaint about Windows 10 Always On VPN is that device tunnel or user tunnel VPN connections fail to reconnect automatically after a laptop computer wakes from sleep or hibernate. You will find many complaining about this issue and discussing various attempts at resolution on the Microsoft forums. And while Microsoft has released many fixes the last few years to improve connection reliability for Always On VPN, this one seems to continue to plague them. This issue is also prevalent with DirectAccess deployments.
