Top 5 DirectAccess Troubleshooting PowerShell Commands

Top 5 DirectAccess Troubleshooting PowerShell CommandsNative PowerShell commands in Windows 10 make DirectAccess troubleshooting much easier than older operating systems like Windows 7. For example, with one PowerShell command an administrator can quickly determine if a DirectAccess client has received the DirectAccess client settings policy. In addition, PowerShell can be used to view the status of the connection and retrieve additional information or error codes that can be helpful for determining the cause of a failed connection. Further, PowerShell can also be used to review configuration details and perform other troubleshooting and connectivity validation tasks.

Here are my top 5 PowerShell commands for troubleshooting DirectAccess on Windows 10.

1. Get-DAClientExperienceConfiguration

Ensuring that the DirectAccess Client Settings group policy has been applied to the client is one of the first steps in troubleshooting failed DirectAccess connections. While it is possible to use gpresult to do this, using the Get-DAClientExperienceConfiguration PowerShell command is much simpler. If DirectAccess client settings have been applied, the output of the command will include information such as the IPsec tunnel endpoint IPv6 addresses and the Network Connectivity Assistant (NCA) corporate resource URL. If DirectAccess client settings have not been applied, this information will be missing.

Top 5 DirectAccess Troubleshooting PowerShell Commands

Figure 1. DirectAccess Client Settings group policy successfully applied.

Top 5 DirectAccess Troubleshooting PowerShell Commands

Figure 2. DirectAccess Client Settings group policy not applied.

2. Get-NetIPHttpsState

Performance improvements first introduced in Windows 8 have made IP-HTTPS the IPv6 transition technology of choice when it comes to supporting DirectAccess client connectivity. Also, if the DirectAccess server is located behind an edge device performing Network Address Translation (NAT), IP-HTTPS is the only supported transition technology. Using the Get-NetIPHttpsState PowerShell command, the DirectAccess administrator can quickly determine if the IP-HTTPS connection was successful. If it was not, the command will return an error code and interface status that will indicate why the IP-HTTPS connection was unsuccessful.

Top 5 DirectAccess Troubleshooting PowerShell Commands

Figure 3. Get-NetIPHttpsState

3. Get-NetIPHttpsConfiguration

When troubleshooting IP-HTTPS connection failures, it is necessary to obtain additional information to continue the troubleshooting process. Using the Get-NetIPHttpsConfiguration PowerShell command, the DirectAccess administrator can obtain the public hostname for the DirectAccess server and ensure that the name resolves to the correct IP address in DNS and that it is reachable on TCP port 443.

Top 5 DirectAccess Troubleshooting PowerShell Commands

Figure 4. Get-NetIPHttpsConfiguration

4. Resolve-DnsName

Using the Resolve-DnsName PowerShell command is crucial when performing any name resolution tasks on the DirectAccess client. This is because Resolve-DnsName is aware of the Name Resolution Policy Table (NRPT) and will direct name resolution requests accordingly. Tools like nslookup are DNS server testing tools and are unaware of the NRPT. Typically they do not yield expected results when testing name resolution on a DirectAccess client.

Top 5 DirectAccess Troubleshooting PowerShell Commands

Figure 5. Name resolution results from Resolve-DnsName and nslookup.

5. Get-DnsClientNrptPolicy

Often the cause of DirectAccess client connectivity issues is a misconfigured NRPT. Using the Get-DnsClientNrptPolicy PowerShell command the DirectAccess administrator can validate that name resolution requests for host names in any internal namespaces are being sent to the DirectAccess DNS64 IPv6 address.

Top 5 DirectAccess Troubleshooting PowerShell Commands

Figure 6. Get-DnsClientNrptPolicy

Additional Resources

Top 5 DirectAccess Troubleshooting Tips

Troubleshooting Name Resolution Issues on DirectAccess Clients

Learn PowerShell in a Month of Lunches Book by Don Jones and Jeff Hicks

Implementing DirectAccess with Windows Server 2016 Book

Planning and Implementing DirectAccess with Windows Server 2016 Video Training Course

Managing and Supporting DirectAccess with Windows Server 2016 Video Training Course

 

 

Planning and Implementing DirectAccess with Windows Server 2016 Video Training Course on Pluralsight

Planning and Implementing DirectAccess with Windows Server 2016I’m excited to announce my latest video training course, Planning and Implementing DirectAccess with Windows Server 2016, is now available on Pluralsight! In this course, I’ll provide a high-level overview of DirectAccess, compare it with VPN, and outline supporting infrastructure requirements. In addition, you’ll learn how to choose the best network topology for a DirectAccess deployment, how to prepare Active Directory and Public Key Infrastructure (PKI) for DirectAccess, and how to install and configure DirectAccess in Windows Server 2016 using the latest implementation and security best practices. You’ll also learn how to provision Windows 10 clients and understand the unique requirements for supporting Windows 7.

The course includes the following training modules:

Overview of DirectAccess
Planning for DirectAccess
Configuring DirectAccess with the Getting Started Wizard
Configuring DirectAccess with the Remote Access Setup Wizard
Provisioning DirectAccess Clients
Supporting Windows 7 Clients

Throughout the course, I share valuable knowledge and insight gained from more than 5 years of experience deploying DirectAccess for some of the largest organizations in the world. Pluralsight offers a free trial subscription if you don’t already have one, so watch my DirectAccess video training course today!

Additional Resources

Planning and Implementing DirectAccess with Windows Server 2016 on Pluralsight
Implementing DirectAccess with Windows Server 2016

DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler

Introduction

Communication between the DirectAccess client and server takes place exclusively over IPv6. When DirectAccess servers and/or clients are on the IPv4 Internet, an IPv6 transition technology must be employed to allow those clients to connect to the DirectAccess server. DirectAccess deployment best practices dictate that only the IP-HTTPS IPv6 transition technology be used. IP-HTTPS uses SSL/TLS for server authentication and optionally encryption. To improve security and performance for IP-HTTPS, an Application Delivery Controller (ADC) like the Citrix NetScaler can be configured to perform SSL offloading and client preauthentication for DirectAccess IP-HTTPS connections.

Please note that the following caveats apply when enabling SSL offload for DirectAccess clients:

  • Enabling SSL offload and IP-HTTPS preauthentication on an ADC for DirectAccess is formally unsupported by Microsoft.
  • SSL offload should not be enabled with DirectAccess is configured to use one-time password (OTP) authentication. Offloading SSL will break OTP functionality.

IP-HTTPS Challenges

The IP-HTTPS IPv6 transition technology is a simple and effective way to allow DirectAccess clients and servers to communicate by encapsulating IPv6 traffic in HTTP and routing it over the public IPv4 Internet. However, there are two critical issues with the default implementation of IP-HTTPS in DirectAccess. One is a security issue, the other affects performance.

Security

The DirectAccess server does not authenticate clients establishing IP-HTTPS connections. This could allow an unauthorized client to obtain an IPv6 address from the DirectAccess server using the IPv6 Neighbor Discovery (ND) process. With a valid IPv6 address, the unauthorized user could perform internal network reconnaissance or launch a variety of Denial of Service (DoS) attacks on the DirectAccess infrastructure and connected clients. More details here.

Performance

Windows 7 DirectAccess clients use encrypted cipher suites when establishing IP-HTTPS connections. However, the payload being transported is already encrypted using IPsec. This double encryption increases resource utilization on the DirectAccess server, reducing performance and limiting scalability. More details here.


Note: Beginning with Windows Server 2012 and Windows 8, Microsoft introduced support for null encryption for IP-HTTPS connections. This eliminates the needless double encryption, greatly improving scalability and performance for DirectAccess clients using IP-HTTPS.


SSL Offload for DirectAccess IP-HTTPS

The Citrix NetScaler can be configured to perform SSL offload to improve performance for Windows 7 DirectAccess clients using IP-HTTPS. Since DirectAccess does not natively support SSL offload, the NetScaler must be configured in a non-traditional way. While the NetScaler will be configured to terminate incoming IP-HTTPS SSL connections, it must also use SSL for the back-end connection to the DirectAccess server. However, the NetScaler will be configured only to use null cipher suites when connecting to the DirectAccess server. Even though Windows 7 clients will still perform double encryption to the NetScaler, this configuration effectively offloads from the server the heavy burden of double encrypting every IP-HTTPS connection for all connected DirectAccess clients. This results in reduced CPU utilization on the DirectAccess server, yielding better scalability and performance.

SSL Offload and Windows 8.x/10 Clients

Offloading SSL for Windows 8.x/10 clients will not improve performance because they already use null cipher suites for IP-HTTPS when connecting to a Windows Server 2012 or later DirectAccess server. However, terminating SSL on the NetScaler is still required to perform IP-HTTPS preauthentication.

Supported NetScaler Platforms for DirectAccess SSL Offloading

The following configuration for Citrix NetScaler can be performed on any release of the VPX virtual ADC platform. However, be advised that there is a known issue with older releases on the MDX and SDX hardware platforms that will prevent this from working. For MDX and SDX deployments, upgrading to release 11.1 build 50.10 or later will be required.

Configure Citrix NetScaler for IP-HTTPS SSL Offload

To enable SSL offloading for DirectAccess IP-HTTPS on the Citrix NetScaler, open the NetScaler management console, expand Traffic Management and Load Balancing, and then perform the following procedures in order.

Add Servers

  1. Click Servers.
  2. Click Add.
  3. In the Name field enter a descriptive name for the first DirectAccess server.
  4. Select IP Address.
  5. In the IP Address field enter the IP address of the first DirectAccess server.
  6. Click Create.
  7. Repeat these steps for any additional servers in the load-balanced cluster.

DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler

Add Services

  1. Click Services.
  2. Click Add.
  3. In the Service Name field enter a descriptive name for the service.
  4. Select Existing Server from the Server drop-down list.
  5. Choose the first DirectAccess server in the cluster.
  6. Choose SSL from the Protocol drop-down list.
  7. Click Ok.DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler
  8. Edit SSL Parameters.
    1. In the Protocol section uncheck SSLv3.
    2. Click Ok.
  9. Edit SSL Ciphers.
    1. Click Remove All.
    2. Click Add.
    3. Type NULL in the Search Ciphers box.
    4. Check the box next to the first entry for SSL3-NULL-SHA.
    5.  Click the right arrow to add the cipher to the list.
    6. Click Ok.
    7. Click Done.
    8. Repeat these steps for any additional servers in the load-balanced cluster.DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler

A warning message may be displayed indicating that no usable ciphers are configured on the SSL vserver/service. This message can be safely ignored.

DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler

Add Virtual Server

  1. Click Virtual Servers.
    1. Click Add.
    2. In the Name field enter a descriptive name for the virtual server.
    3. Choose SSL from the Protocol drop-down list.
    4. In the IP Address field enter the IP address for the virtual server.
    5. Click Ok.DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler

      Note: When enabling load balancing in DirectAccess, the IP address assigned to the first DirectAccess server is reallocated for use as the load balancing Virtual IP Address (VIP). Ideally this IP address will be assigned to the load balancing virtual server on the NetScaler. However, this is not a hard requirement. It is possible to configure the VIP on the NetScaler to reside on any subnet that the load balancer has an interface to. More details here.


  2. In the Services and Groups section click No Load Balancing Virtual Server Service Binding.
    1. Click on the Select Service field.
    2. Check all DirectAccess server services and click Select.
    3. Click Bind.
    4. Click Continue.
  3. In the Certificate section click No Server Certificate.
    1. Click on the Select Server Certificate field.
    2. Choose the certificate to be used for DirectAccess IP-HTTPS.
    3. Click Select.
    4. Click Bind.
    5. Click Continue.
  4. Edit SSL Ciphers.
    1. Click Remove All.
    2. Click Add.
    3. Type ECDHE in to the Search Ciphers box.
    4. Check the box next to TLS1-ECDHE-RSA-AES128-SHA.
    5. Click the right arrow to add the cipher to the list.
    6. Type NULL in to the Search Ciphers box.
    7. Check the box next to SSL3-NULL-SHA.
    8. Click the right arrow to add the cipher to the list.
    9. Click Ok.
    10. Click Done.DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler

      Note: If Windows 8.x/10 clients are supported exclusively, SSL3-NULL-SHA is the only cipher suite required to be configured on the virtual server. If Windows 7 client support is required, the TLS1-ECDHE-RSA-AES128-SHA cipher suite should also be configured on the virtual server.


  5. Edit SSL Parameters.
    1. Uncheck SSLv3.
    2. Click Ok.

      Note: If Windows 8.x/10 clients are supported exclusively, TLSv1 can also be unchecked on the virtual server. If Windows 7 client support is required, TLSv1 must be enabled.


  6. In the Advanced Settings section click Persistence.
    1. Choose SSLSESSION.
    2. Enter 10 minutes for the Time-out (mins) value.
    3. Click Ok.
    4. Click Done.

Optional IP-HTTPS Preauthentication

To enable IP-HTTPS preauthentication to prevent unauthorized network access, perform the following procedures on the Citrix NetScaler appliance.

  1. Expand Traffic Management, Load Balancing, and then click Virtual Servers.
  2. Select the DirectAccess virtual server and click Edit.
    1. In the Certificate section click No CA Certificate.
    2. Click the Select CA Certificate field.
    3. Choose the certificate for the CA that issues certificates to DirectAccess clients and servers.

      Note: The CA certificate used for DirectAccess can be found by opening the Remote Access Management console, clicking Edit on Step 2, and then clicking Authentication. Alternatively, the CA certificate can be found by running the following PowerShell command.

      (Get-RemoteAccess).IPsecRootCertificate | Format-Table Thumbprint


    4. Click Select.
    5. Choose CRL Optional from the CRL and OCSP Check drop-down list.
    6. Click Bind.
  3. Edit SSL Parameters.
    1. Check the box next to Client Authentication.
    2. Choose Mandatory from the Client Certificate drop-down list.
    3. Click Ok.
    4. Click Done.
      DirectAccess SSL Offload and IP-HTTPS Preauthentication with Citrix NetScaler

Summary

Leveraging the advanced capabilities of the Citrix NetScaler ADC can improve performance when supporting Windows 7 clients and enhance security for all DirectAccess clients using IP-HTTPS. In terms of supportability, all of the changes described in this article are completely transparent and do not alter the native DirectAccess client or server configuration. If a Microsoft support engineer declines support due to this configuration, switching from SSL offload to SSL bridge is all that’s required to restore full supportability.

Additional Resources

NetScaler release 11.1 build 50.10 (requires login) – https://www.citrix.com/downloads/netscaler-adc/firmware/release-111-build-5010

Release notes for build 50.10 of NetScaler 11.1 release – https://www.citrix.com/content/dam/citrix/en_us/documents/downloads/netscaler-adc/NS_11_1_50_10.html

VIDEO: Enable Load Balancing for DirectAccess – https://www.youtube.com/watch?v=3tdqgY9Y-uo

DirectAccess IP-HTTPS preauthentication using F5 BIG-IP – https://directaccess.richardhicks.com/2016/05/23/directaccess-ip-https-preauthentication-using-f5-big-ip/

DirectAccess SSL offload for IP-HTTPS using F5 BIG-IP – https://directaccess.richardhicks.com/2013/07/10/ssl-offload-for-ip-https-directaccess-traffic-from-windows-7-clients-using-f5-big-ip/

Implementing DirectAccess with Windows Server 2016 book – http://directaccessbook.com/

%d bloggers like this: