Always On VPN IKEv2 Features and Limitations

Always On VPN IKEv2 Features and LimitationsThe Internet Key Exchange version 2 (IKEv2) VPN protocol is a popular choice for Windows 10 Always On VPN deployments. IKEv2 is a standards-based IPsec VPN protocol with customizable security parameters that allows administrators to provide the highest level of protection for remote clients. In addition, it provides important interoperability with a variety of VPN devices, including Microsoft Windows Server Routing and Remote Access Service (RRAS) and non-Microsoft platforms such as Cisco, Checkpoint, Palo Alto, and others.

IKEv2 Limitations

IKEv2 is clearly the protocol of choice in terms of security. It supports modern cryptography and is highly resistant to interception. It’s not without some operational challenges, however. Consider the following.

Firewalls

IKEv2 uses UDP ports 500 and 4500 for communication. Unfortunately, these ports are not always open. Often, they are blocked by network administrators to prevent users from bypassing security controls or attackers from exfiltrating data.

Fragmentation

IKEv2 packets can become quite large at times, especially when using client certificate authentication with the Protected Extensible Authentication Protocol (PEAP). This can result in fragmentation occurring at the network layer. Unfortunately, many firewalls and network devices are configured to block IP fragments by default. This can result in failed connection attempts from some locations but not others.

Load Balancing

Load balancing IKEv2 connections is not entirely straightforward. Without special configuration, load balancers can cause intermittent connectivity issues for Always On VPN connections. Guidance for configuring IKEv2 load balancing on the Kemp LoadMaster and the F5 BIG-IP can be found here:

IKEv2 Fragmentation

IKEv2 fragmentation can be enabled to avoid IP fragmentation and restore reliable connectivity. IKEv2 fragmentation is supported in Windows 10 and Windows Server beginning with v1803. Guidance for enabling IKEv2 fragmentation on Windows Server RRAS can be found here. Support for IKEv2 fragmentation on non-Microsoft firewall/VPN devices is vendor-specific. Consult with your device manufacturer for more information.

IKEv2 Security and RRAS

Be advised that the default security settings for IKEv2 on Windows Server RRAS are very poor. The minimum recommended security settings and guidelines for implementing them can be found here.

IKEv2 or TLS?

IKEv2 is recommend for deployments where the highest level of security and protection is required for remote connections. In these scenarios, the sacrifice of ubiquitous availability in favor of ultimate security might be desired.

SSTP or another TLS-based VPN protocol is recommended if reliable operation and connectivity are desired. SSTP and TLS VPNs can be configured to provide very good security by following the security and implementation guidelines found here.

IKEv2 with TLS Fallback

In theory, preferring IKEv2 and falling back to the Secure Socket Tunneling Protocol (SSTP) or another TLS-based VPN protocol when IKEv2 is unavailable would seem like a logical choice. This would ensure the highest level of protection, while still providing reliable connectivity. Unfortunately, the Windows VPN client doesn’t work this way in practice. Details here.

Additional Information

Windows 10 Always On VPN IKEv2 Load Balancing with F5 BIG-IP

Windows 10 Always On VPN IKEv2 Load Balancing with Kemp LoadMaster

Windows 10 Always On VPN IKEv2 Fragmentation

Windows 10 Always On VPN IKEv2 and SSTP Fallback

Windows 10 Always On VPN IKEv2 Security Configuration

Windows 10 Always On VPN Certificate Requirements for IKEv2

Windows 10 Always On VPN Protocol Recommendations for Windows Server RRAS

Always On VPN IKEv2 Load Balancing with F5 BIG-IP

Always On VPN IKEv2 Load Balancing with F5 BIG-IPThe Internet Key Exchange version 2 (IKEv2) is the protocol of choice for Always On VPN deployments where the highest level of security is required. Implementing Always On VPN at scale often requires multiple VPN servers to provide sufficient capacity and to provide redundancy. Commonly an Application Delivery Controller (ADC) or load balancer is configured in front of the VPN servers to provide scalability and high availability for Always On VPN.

Load Balancing IKEv2

In a recent post I described some of the unique challenges load balancing IKEv2 poses, and I demonstrated how to configure the Kemp LoadMaster load balancer to properly load balance IKEv2 VPN connections. In this post I’ll outline how to configure IKEv2 VPN load balancing on the F5 BIG-IP load balancer.

Note: This article assumes the administrator is familiar with basic F5 BIG-IP load balancer configuration, such as creating nodes, pools, virtual servers, etc.

Initial Configuration

Follow the steps below to create a virtual server on the F5 BIG-IP to load balance IKEv2 VPN connections.

Pool Configuration

To begin, create two pools on the load balancer. The first pool will be configured to use UDP port 500, and the second pool will be configured to use UDP port 4500. Each pool is configured with the VPN servers defined as the individual nodes.

Always On VPN IKEv2 Load Balancing with F5 BIG-IP

Virtual Server Configuration

Next create two virtual servers, the first configured to use UDP port 500 and the second to use UDP port 4500.

Always On VPN IKEv2 Load Balancing with F5 BIG-IP

To ensure reliable connectivity for IKEv2 connections it is necessary for the VPN server to see the client’s original source IP address. When configuring virtual server, select None from the Source Address Translation drop-down list.

Always On VPN IKEv2 Load Balancing and NAT

Persistence Profile

To ensure that both IKEv2 UDP 500 and 4500 packets are delivered to the same node, follow the steps below to create and assign a Persistence Profile.

1. Expand Local Traffic > Profiles and click Persistence.
2. Click Create.
3. Enter a descriptive name for the profile in the Name field.
4. Select Source Address Affinity from the Persistence Type drop-down list.
5. Click the Custom check box.
6. Select the option to Match Across Services.
7. Click Finished.

Always On VPN IKEv2 Load Balancing with F5 BIG-IP

Assign the new persistence profile to both UDP 500 and 4500 virtual servers. Navigate to the Resources tab on each virtual server and select the new persistence profile from the Default Persistence Profile drop-down list. Be sure to do this for both virtual servers.

Always On VPN IKEv2 Load Balancing with F5 BIG-IP

Additional Resources

Windows 10 Always On VPN IKEv2 Load Balancing and NAT

Windows 10 Always On VPN IKEv2 Load Balancing with Kemp LoadMaster Load Balancer 

Windows 10 Always On VPN IKEv2 Security Configuration

Windows 10 Always On VPN and IKEv2 Fragmentation

Windows 10 Always On VPN Certificate Requirements for IKEv2

Video: Windows 10 Always On VPN Load Balancing with the Kemp LoadMaster Load Balancer