Always On VPN SSTP Connects then Disconnects

Always On VPN SSTP Connects then DisconnectsWhen Always On VPN clients are configured to use the Secure Socket Tunneling Protocol (SSTP) with Windows Server Routing and Remote Access Service (RRAS), administrators may encounter a scenario in which a client can establish a VPN connection using SSTP successfully, but is then disconnected immediately. The system event log contains an entry with Event ID 6 from the RasSstp source that includes the following error message.

“The SSTP-based VPN connection to the remote access server was terminated because of a security check failure. Security settings on the remote access server do not match settings on this computer. Contact the system administrator of the remote access server and relay the following information.”

Always On VPN Connect and Disconnect with SSTP

Common Causes

The two most common causes of this issue are when SSTP is configured for SSL offload, and when a VPN client is on a network where SSL inspection is taking place.

SSTP Offload

The most common cause of this issue is when SSL offload is configured for SSTP on an external load balancer or application delivery controller (ADC). To prevent interception from a Man-in-the-Middle attack, the VPN client sends the certificate hash of the SSL certificate used when the VPN connection was established. If this information does not match what is configured on the RRAS server, the connection is assumed to be compromised and the connection is immediately dropped.

SSL Inspection

Another scenario where this issue may occur is when a VPN client is behind a network device configured to perform SSL deep-packet inspection (DPI). SSTP VPN clients will be unable to connect to the VPN server in this scenario.

Resolution

When offloading SSL to another device, the RRAS server must be configured to know which SSL certificate is being presented to remote clients. This information is stored in the following registry key.

HKLM:\SYSTEM\CurrentControlSet\Services\SstpSvc\Parameters\SHA256CertificateHash

However, this registry entry requires a binary value, which makes it a challenge to configure manually. To resolve this problem, it is recommended that the same SSL certificate installed on the load balancer/ADC also be installed on the VPN server (even though SSL will be offloaded). To do this, first import the SSL certificate and private key in to the Local Computer certificate store, then open the RRAS management console and perform the following steps.

  1. Right-click the VPN server and choose Properties.
  2. Select the Security tab.
  3. Uncheck Use HTTP in the SSL Certificate Binding section.
  4. Select the appropriate SSL certificate from the Certificate drop-down list (click View to verify).
  5. Click Apply.

This will add the correct SSL certificate information to the registry. Next, re-enable HTTP for SSL offload by performing the following steps.

  1. Check Use HTTP in the SSL Certificate Binding section.
  2. Click Apply.

PowerShell Configuration

If the SSL certificate cannot be installed on the VPN server, or to automate this configuration across multiple servers remotely, download and run the Enable-SstpOffload PowerShell script from my GitHub repository here and run the following command.

Enable-SSTPOffload -CertificateHash [SHA256 Certificate Hash of Public SSL Certificate] -Restart

For example…

Enable-SSTPOffload -CertificateHash “C3AB8FF13720E8AD9047DD39466B3C8974E592C2FA383D4A3960714CAEF0C4F2” -Restart

Additional Information

Windows 10 Always On VPN Load Balancing and SSL Offload

Windows 10 Always On VPN SSTP Load Balancing with F5 BIG-IP

Windows 10 Always On VPN SSL Certificate Requirements for SSTP

Windows 10 Always On VPN Protocol Recommendations for Windows Server RRAS

 

Always On VPN SSTP Load Balancing and SSL Offload

SSL Certificate Considerations for DirectAccess IP-HTTPSThe Windows Server Routing and Remote Access Service (RRAS) is a popular choice for a VPN server to support Windows 10 Always On VPN deployments. One significant advantage RRAS provides is support for the Secure Socket Tunneling Protocol (SSTP). SSTP is a Microsoft proprietary VPN protocol that uses Transport Layer Security (TLS) to ensure privacy between the VPN client and server. The advantage to using a TLS-based transport is that it leverages the standard HTTPS TCP port 443, making it firewall friendly and ensuring ubiquitous remote access even behind highly restrictive firewalls.

Load Balancing SSTP

Load balancing SSTP can be accomplished in much the same way as a load balancing a common web server using HTTPS. The external load balancer is configured with a virtual IP address (VIP) and each VPN server is configured behind it. Session persistence should be configured to use SSL with source IP address persistence as a fallback.

SSL Offload for SSTP

In most cases, simply forwarding encrypted SSTP connections to the VPN server will be sufficient. However, offloading SSL/TLS processing to an Application Delivery Controller (ADC) or load balancer can be beneficial for the following reasons.

Resource Utilization

Enabling TLS offload for SSTP VPN connections can reduce CPU and memory utilization on the VPN server. However, this will likely only be necessary for very busy servers supporting many concurrent connections.

Security

In some cases, the administrator may not be able to install the public SSL certificate on the VPN server. For example, a security policy may exist that restricts SSL certificate installation to dedicated security devices using a Hardware Security Module (HSM). In some cases, it may be desirable to restrict access to high value certificates such as wildcard certificates.

Certificate Management

Often SSL certificates are implemented on load balancers to reduce certificate sprawl and to ease the management and administration burden in the enterprise. By having all enterprise certificates installed only on dedicated security devices, administrators can more effectively monitor and manage SSL certificate lifecycles.

SSTP Configuration for TLS Offload

Configuration changes must be made on the load balancer and the RRAS server to support TLS offload for SSTP.

Load Balancer

Install the public SSL certificate on the load balancer and configure it for TLS termination. Configure the load balancer to then use HTTP for backend server connections. Consult the load balancer vendor’s documentation for configuration guidance.

Load Balancing Always On VPN SSTP Load Balancing with F5 BIG-IP

RRAS Server

If the public SSL certificate is installed on the VPN server, enabling TLS offload for SSTP is simple and straightforward. Follow the steps below to enable TLS offload for SSTP VPN connections.

  1. Open the RRAS management console (rrasmgmt.msc).
  2. Right-click the VPN server and choose Properties.
  3. Select the Security tab.
  4. Check Use HTTP in the SSL Certificate Binding section.
  5. Click Ok and then Yes to restart the Remote Access service.

Always On VPN SSTP Load Balancing and SSL Offload

If the public SSL certificate is not or cannot be installed on the RRAS server, additional configuration will be required. Specifically, SSL offload for SSTP must be configured using the Enable-SSTPOffload PowerShell script, which can be downloaded here.

Once the script has been downloaded and imported, open an elevated PowerShell command window and enter the following command.

Enable-SSTPOffload -CertificateHash [SHA256 Certificate Hash of Public SSL Certificate] -Restart

For example…

Enable-SSTPOffload -CertificateHash “C3AB8FF13720E8AD9047DD39466B3C8974E592C2FA383D4A3960714CAEF0C4F2” -Restart

Re-Encryption

When offloading TLS for SSTP VPN connections, all traffic between the load balancer and the VPN server will be sent in the clear using HTTP. In some scenarios, TLS offload is required only for traffic inspection, not performance gain. When terminating TLS on the load balancer and re-encrypting connections to the VPN server is required, it is only supported if the same certificate is used on both the load balancer and the VPN server.

Additional Information

Windows 10 Always On VPN SSL Certificate Requirements for SSTP

Windows 10 Always On VPN SSL Load Balancing with F5 BIG-IP

Windows 10 Always On VPN IKEv2 and SSTP Fallback

Windows 10 Always On VPN Hands-On Training Classes for 2019

Always On VPN SSL Certificate Requirements for SSTP

Always On VPN Certificate Requirements for SSTPThe Windows Server 2016 Routing and Remote Access Service (RRAS) is commonly deployed as a VPN server for Windows 10 Always On VPN deployments. Using RRAS, Always On VPN administrators can take advantage of Microsoft’s proprietary Secure Socket Tunneling Protocol (SSTP) VPN protocol. SSTP is a Transport Layer Security (TLS) based VPN protocol that uses HTTPS over the standard TCP port 443 to encapsulate and encrypt communication between the Always On VPN client and the RRAS VPN server. SSTP is a firewall-friendly protocol that ensures ubiquitous remote network connectivity. Although IKEv2 is the protocol of choice when the highest level of security is required for VPN connections, SSTP can still provide very good security when implementation best practices are followed.

SSTP Certificate

Since SSTP uses HTTPS for transport, a common SSL certificate must be installed in the Local Computer/Personal/Certificates store on the RRAS VPN server. The certificate must include the Server Authentication Enhanced Key Usage (EKU) at a minimum. Often SSL certificates include both the Server Authentication and Client Authentication EKUs, but the Client Authentication EKU is not strictly required. The subject name on the certificate, or at least one of the Subject Alternative Name entries, must match the public hostname used by VPN clients to connect to the VPN server. Multi-SAN (sometimes referred to as UC certificates) and wildcard certificates are supported.

Always On VPN Certificate Requirements for SSTP

Certification Authority

It is recommended that the SSL certificate used for SSTP be issued by a public Certification Authority (CA). Public CAs typically have their Certificate Revocation Lists (CRLs) hosted on robust, highly available infrastructure. This reduces the chance of failed VPN connection attempts caused by the CRL being offline or unreachable.

Using an SSL certificate issued by an internal, private CA is supported if the CRL for the internal PKI is publicly available.

Key Type

RSA is the most common key type used for SSL certificates. However, Elliptic Curve Cryptography (ECC) keys offer better security and performance, so it is recommended that the SSTP SSL certificate be created using an ECC key instead.

Always On VPN Certificate Requirements for SSTP

To use an ECC key, be sure to specify the use of a Cryptographic Next Generation (CNG) key and select the ECDSA_P256 Microsoft Software Key Storage Provider (CSP) (or greater) when creating the Certificate Signing Request (CSR) for the SSTP SSL certificate.

Always On VPN Certificate Requirements for SSTP

Most public CAs will support certificate signing using ECC and Elliptic Curve Digital Signature Algorithm (ECDSA). If yours does not, find a better CA. 😉

Forward Secrecy

Forward secrecy (sometimes referred to as perfect forward secrecy, or PFS) ensures that session keys can’t be compromised even if the server’s private key is compromised. Using forward secrecy for SSTP is crucial to ensuring the highest levels of security for VPN connections.

To enforce the use of forward secrecy, the TLS configuration on the VPN server should be prioritized to prefer cipher suites with Elliptic Curve Diffie-Hellman Ephemeral (ECDHE) key exchange.

Authenticated Encryption

Authenticated encryption (AE) and authenticated encryption with associated data (AEAD) is a form of encryption that provides better data protection and integrity compared to older block or stream ciphers such as CBC or RC4.

To enforce the use of authenticated encryption, the TLS configuration on the VPN server should be prioritized to prefer cipher suites that support Galois/Counter Mode (GCM) block ciphers.

Important Note: In Windows Server 2016, GCM ciphers can be used with both RSA and ECC certificates. However, in Windows Server 2012 R2 GCM ciphers can only be used when an ECC certificate is used.

SSL Offload

Offloading SSL to a load balancer or application delivery controller (ADC) can be enabled to improve scalability and performance for SSTP VPN connections. I will cover SSL offload for SSTP in detail in a future post.

Summary

SSTP can provide good security for VPN connections when implementation and security best practices are followed. For optimum security, use an SSL certificate with an EC key and optimize the TLS configuration to use forward secrecy and authenticated cipher suites.

Additional Information

Always On VPN ECDSA SSL Certificate Request for SSTP

Always On VPN and Windows Server Routing and Remote Access Service (RRAS)

Always On VPN Protocol Recommendations for Windows Server RRAS

Always On VPN Certificate Requirements for IKEv2

3 Important Advantages of Always On VPN over DirectAccess

Microsoft SSTP Specification on MSDN